Newstar KVM Switch, 8-port, PS/2, USB, IP Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Przełączniki KVM Newstar KVM Switch, 8-port, PS/2, USB, IP. Newstar KVM over IP module, PS/2, USB Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj

Podsumowanie treści

Strona 1 - NS-1641HDI

1, 8 & 16 PORT DIGITAL IP KVM SWITCH User ManualNS-1105IPEXTNS-841HDINS-1641HDIwww.newstar.nl

Strona 2 - Table of Content

8Step 5. Change “Bits per second” to 115200. Step 6. Press “Enter”, you will get the following screen. Step 7. Follow the instruction on the screen. F

Strona 3

9----- Installing the NewStar Digital KVM via IP NOTE: The instructions here and elsewhere in the manual refer to port designations of the NS1641HDI,

Strona 4 - ----- Before You Begin

10NOTE: You can choose to mix managed computers connected via PS/2 and USB connections as necessary with no impact on features or functionality. NOTE:

Strona 5 - ----- Quick Start Guide

11unit is powered on and connected to the network via LAN port on the rear panel, it will automatically attempt to lease an IP address using DHCP. Be

Strona 6

12Connection speed: 115200 bps No. of bits: 8 Parity: None Stop bits: 1 Flow Control: None ----- Configuring the KVM for Your Network NOTE: As firmwar

Strona 7

13The Home Screen The Home screen serves two functions. First, it is a place to check the status of the unit, view essential system information, and

Strona 8

14Commit Network Changes Clicking the Commitbutton applies any changes made on the page to the configuration, but leaves the old settings active until

Strona 9

15Setup compatibility with host system, external power bar.This menu allows you to configure the unit for use with products such as the Serial Control

Strona 10

16given at the RADIUS prompt, the system will use “name”; check the password locally, and skip RADIUS authentication. Delete all local accounts to avo

Strona 11 - (Power)

17If you have multiple units to upgrade, you may choose the Get latest version button that will not attempt to upgrade the unit directly, but will ins

Strona 12

Table of Content  INTRODUCTION ...2 FEATURES...

Strona 13

18-----------------------------------Digital KVM via IP Network Setup-----------------------------------NOTE: This interface is used to set network pa

Strona 14 - Using the Web Interface

19This program has a simple menu-based interface. Type the one letter command and press Enter. You will be prompted for the required values. NOTE: y

Strona 15

20connection is a standard SSL (Secure Socket Layer) encrypted link that encrypts all data from the session, including the actual video pictures. Beca

Strona 16

21----- Using the VNC Menu One of the unique features of this product is the VNC menu system. Whenever you see a window with a dark blue background a

Strona 17

22PS/2 Reset: Resets the PS/2 keyboard and mouse emulation. Useful to recover failed mouse and/or keyboard connections. ÷4, ÷8: Switches to thumbnail

Strona 18

23The main menu window may be moved by clicking and dragging on the title bar. It can be closed by pressing Escape, or by clicking on the red X in the

Strona 19

24key at the same time. Alternatively, you may move the mouse outside this window, press the regular key, and then choose -RESET- to release all depre

Strona 20

25Pressing the Advanced button will open the Advanced Video Tuning menu. While the vast majority of users will not need to adjust these settings, it

Strona 21 - Web Interface

26OSD Operations (For NS431D, NS831D, NS1631D AND IP units only) OSD screen illustration y NS431D / NS831D / NS1631D models offer “F5”, see Function

Strona 22 - Native VNC Client

27the Enter key to select it. Or, you may press Esc to exit OSD and remove the OSD menu from the display; the status window returns to the displa

Strona 23 - Bribar Feature

Video Tuning Menu... 24  ACCESSING KVM FEATURES .

Strona 24 - Main Menu

28 Auto ScanIn this mode, the KVM switch automatically switches from one power-on computer to the next sequentially in a fixed interval. During Auto

Strona 25 - VirtKeys Menu

29 CH Display Auto Off: After you select a computer, the port number and name of the computer will appear on the screen for 3 seconds then disappear

Strona 26 - Video Tuning Menu

30Hot Key Commands A hot key command is a short keyboard sequence to select a computer, activate a computer scan, etc. A hot-key sequence starts with

Strona 27 - Cascade Configuration

31left Ctrl + left Ctrl + F3 1The unit switches between scan intervals of 3, 8, 15 and 30 seconds. Keyboard Typematic Rate You can adjust th

Strona 28

32----- Troubleshooting If you are experiencing trouble with your devices, first make sure that all cables are connected to their proper ports and are

Strona 29

33VGA image is not clear. You may be using poor quality VGA cables. Make sure you are using UL-2919 rated, double-shielded VGA cables. The quality of

Strona 30

34Cannot select a computer connected to a Slave. Make sure that the Slave’s Console port is connected to one of the Master’s PC ports. Only ports PC 1

Strona 31 -  Position

35----- Specifications Maximum supported video mode 1600x1200 @ 85Hz Standard video modes supported 640x400 @ 85Hz 720x400 @ 85Hz 640x480 @ 60Hz 640x

Strona 32 - Hot Key Commands

36----- Supported Protocols Service Description BenefitsSSH Secure Shell May be used to securely “tunnel” VNC and HTTP protocols. HTTP Web redirect

Strona 33 - Changing Your Configuration

37----- Warranty Information This product is backed by a one-year warranty. In addition NewStar warrants its products against defects in materials and

Strona 34 - ----- Troubleshooting

2----- Introduction Thank you for purchasing NewStar NewStar Digital KVM via IP series with integrated KVM. Using the Internet or your TCP/IP enabled

Strona 35

38Appendix A: About Security Certificate Warnings What is a security certificate? Sites that employ secure TCP/IP (Internet) connections include a cer

Strona 36

39Appendix B: Using the Advanced Video Tuning Feature The Advanced Video Tuning menu allows you to adjust the qualities of the video in your VNC sessi

Strona 37 - ----- Specifications

40Use the Show Diffs button to learn which parts of the screen are being sent over the Internet. When you click this button, the screen is cleared to

Strona 38 - ----- Supported Protocols

41Appendix C: Getting Peak Performance Choose the best video mode y We recommend using 60Hz refresh rate and 1024x768 resolution. Using a smaller reso

Strona 39 - ----- Warranty Information

42Appendix D: Using Optional Serial Supervisors Background The NewStar Digital KVM via IP offers a unique way to expand the functionality of the base

Strona 40

43able to configure your Serial Supervisor, you must be logged in as admin. Other users will be able to view which devices are active but cannot conf

Strona 41

44Advanced Configuration Using the Integrated SSH Shell In most cases, configuring the NewStar Digital KVM via IP to the same settings as the Serial S

Strona 42

45on the other end of the connection. For Unix systems, the command is: stty –crtscts < /dev/[serial port]y Serial Supervisor devices use a

Strona 43 - Network performance

3----- Quick Start GuideFor this Quick Start Guide, we offer three different easy step-by-step ways, letting you setup this unit very quickly. The Fir

Strona 44 - Background

4b. Right click on "Local Area Connection", and select "Properties" . c. Double click on "Internet Protocol (TCP/IP)".

Strona 45

5d. Click “Advanced…” , then click “Add…” to add up the IP address of “192.168.1.124”, and the Subnet mask of “255.255.255.0”.Step 3. From that comput

Strona 46 - Remote Login via SSH

6Step 4. From the above DHCP log, you can easily find the DHCP assigned an IP to the NewStar Digital KVM via IP, 192.168.22.4. Once you have located t

Strona 47

7Step 3. If you never setup your HyperTerminal before, it will ask you to input your phone area code, please feel free to do so, and then click “OK”,

Komentarze do niniejszej Instrukcji

Brak uwag